Skip to main content

Micro Servos

When I started to take a break from microscopic flying vehicles in 2010 and migrate towards some larger, easier to work with, models (5-20g) I realized that magnetic actuators just weren't going to cut it for control (rudder, elevator, ailerons). Magnetic actuators are heavy and draw power continuously when deflected away from neutral. I needed servos. Servos would provide lots of pulling force for their weight but at the cost of mechanical complexity. Since servos at the weight I needed didn't exist or were out of my price range I decided to further over complicate the situation and build my own.


I started by designing a simple linear servo (lead screw design). The picture above is of my 400mg variant which has a throw of about 0.2", resolution of 0.0015", and can pull about a 25g load. The motor is a brushed 3.2mm diameter coreless design by Shicoh. The gears used are module 0.15 and can be gotten from http://www.kkpmo.com/. The threaded rod is 0000-160, which means it has 160 threads per inch (TPI). Threaded rods in this size (and 120, 90, etc TPI) can be purchased in 1ft lengths from http://www.jimorrisco.com/.

All the control software is done on a PIC microprocessor and the feedback is done magnetically with a hall effect sensor. Here is a video of my first version which is a little heavier and has a bit longer throw; 450mg and 3/8" respectively.


Naturally, once I had this servo design done and working I had to see if I could make a smaller and lighter one. After some thought I figured that if I took apart the 3.2mm motor, threw away the case, and rebuild it as a stepper motor I could cut the servo weight almost in half. I also compacted the design to further reduce the weight. Here you can see all the parts for the servo nicely arranged on a penny.



This servo functions very similarly to the large one described above. The only difference is that I wired the brushed motor as a stepper motor by soldering directly to the 5 contacts on the motor's commutator. This allowed me to get rid of the steel case and use the commutator as the main structural component (backbone) of the servo.


This servo weighs just 190mg, has a throw of 1/8", and a resolution of 0.003". It can pull with a force of about 4g. Overall length is about 3/8". Here is a video of it in action:


These two servos can run at voltages between 3-5v and are controlled with a 1-2ms pulse as is standard for all hobby r/c servos.


Comments

  1. I didn't know that there were companies that made micro servos. I usually use servos for my remote control cars. I've bought the cheap kind, so my servos usually die really quickly. It's nice that it's usually pretty easy for me to find the servos that I need for my remote control cars. I can imagine that it would be difficult for me to find micro servos in my area if I ever needed them.
    http://www.hobbyease.com/servos-for-sale-online-k5

    ReplyDelete

Post a Comment

Other People Thought These Were Cool..

3D Printed Mechanical Pencil

What better way is there to spend multiple consecutive weekends than sitting at your computer, redesigning a mechanism that has existed for decades, all to be able to 3D print something that can be bought at the store for less than $1? ... That's right, anything. However, when your co-worker throws down the gauntlet there is only one thing to do. Take it up.


This is how the 3D printed mechanical pencil came to be. Luckily though, it actually works pretty well and has enough style to spare.  
This pencil has 4 separate parts and was printed fully assembled as shown in the image below. Its about 6" long and 1/2" in diameter at its maximum, not including the pocket clip. It takes standard 0.9mm lead and 7mm diameter erasers. Three extra pieces of lead can be stored behind the eraser. I would have liked to do a more common lead size like 0.7mm or 0.5mm but the feature sizes required to hold lead that small are very difficult to achieve even on high resolution printers. Its …

3D Printed Dial Calipers

3D printing initially interested me because of its ability to create physical parts very quickly with nearly any geometry. By the time I had access to a 3D printer the ability to print virtually any shape had already been well proven and had even become common place. I was then introduced to the idea that multiple parts could be printed together, assembled, and captured. This may seem like a new concept but it is merely a new way of looking at 3D printing. The printer doesn't care how many pieces its printing, or even if they are connected.

I had seen adjustable wrenches printed already assembled. In the same fashion, I designed a c-clamp to try my hand at this concept. The camp worked perfectly. So then the question became "What's next?"


Dial Calipers. Yes. That sounded more than complicated enough with its gears, dials, and half dozen moving parts. I guess the irony of 3D printing a precision measurement tool with, what is normally considered, an imprecise manufac…

3D Printed Tape Measure

Going off the success of my 3D printed dial calipers, I decided to try to print something even more elaborate. But what to print? I contemplated several options but ultimately decided to print a tape measure.


Originally I didn't think a tape measure would be that interesting... I mean, it doesn't even have gears. Once I started piecing it together in my mind and determining the acceptable "cool factor", I realized that the parts count alone was skyrocketing. My calipers had 9 pieces, this tape measure would have well over 100... Now things were getting interesting.

I decided to attempt this based on the parts count and the fact that, if successful, I would be able pull out over 4ft of tape from something about 3" sq. Also, I had no better ideas at the time.


I designed the tricky parts first, then I printed little test pieces here and there to validate the design before integrating them together. Right around the time I starting adding all the cutouts in the main…